Used Snell IQLOG01 SD-SDI Logo InserterUsed Snell IQLOG01 SD-SDI Logo Inserter

Used Snell IQLOG01 SD-SDI Logo Inserter

This Used Snell IQLOG01 SD-SDI Logo Inserter is in a very good condition and in full working order as well it comes with 3 months warranty. We have multiple units available all in full working order and in very good condition.

£75.00 exc. VAT

SKU: IQLOG01 Categories: , Tag:

Please note this is an Used Snell IQLOG01 SD-SDI Logo Inserter. ES Broadcast carefully tests all used equipment prior to sale, and offers a three-month warranty. Images shown are for illustrative purposes only and may not be of the specific model offered for sale. Accurate pictures of this model are available on request.

Snell IQLOG01 provides logo generation and insertion for SD-SDI 270 Mbit/s signals.

The unit is capable of adding up to 4 x SD static 10-bit color logos into the SDI stream at any point within 4:2:2 boundaries of the active picture. Up to 2.6M pixels of logo storage is available. Logo control is via RollCall template, GPI or RollTrack triggers, and logos can be efficiently downloaded over the RollCall network via a PC application and stored in non-volatile memory.

Features:

  • Serial digital logo insertion for SD-SDI signals
  • Ability to insert up to 4 logos into the SD-SDI stream
  • Control of horizontal and vertical logo positioning – at any point within 4:2:2 boundaries of the active picture
  • Logo storage capacity of 2.6M pixels
  • User defined logos can be loaded over a PC network with direct support for TGA, TIFF or BMP based files
  • Video and alpha-channel processing at 10 bits to 4:2:2:4 resolution
  • Totally transparent to ancillary data
  • Smooth fade with dedicated manual or automatic (GPI) fade control
  • Standards/formats supported:
  • 576/50i
  • 480/59i
  • In-built test pattern generator
  • User defined input failure logo
  • Input loss detection – input pass through, black, pattern or logo
  • Input SDI, EDH and ANC data checking, reporting and insertion
  • 4 active SDI outputs
  • 2 x GPIs for control of logo on/off
  • 32 x user memories
  • 60 x logo memories
  • GPI recall of user and logo memories
  • RollCall Control and monitoring compatible
Inputs & Outputs
Signal Inputs
Inputs……………………………. 1 x Serial Digital
Electrical ………………………. 270 Mbit/s SDI, SMPTE 259M-C
Connector / Format…………. BNC/75 ohm panel jack on standard S&W connector panel
Input Cable Length …………. Up to 350 m Belden 1694A @ 270 Mbit/s
Note: Specified cable lengths are a guide only. Exact cable length performance will depend on the quality of the cable used, the SDI video rate and the system setup. It is advisable not to cascade modules using the relay rear version although it may be possible if the interconnecting cable lengths are kept to an absolute minimum.
Return loss……………………………………………. > -15dB
Relay bypass versions
Input Return Loss: ………………. > -8dB (When not in BYPASS mode)
Output Return Loss: …………………………….. > -8dB (When not in BYPASS mode)
Signal Outputs
Outputs …………………………. 4 x Serial Digital
Electrical ………………………. 270 Mbit/s SDI, SMPTE 259M-C
Connector / Format…………. BNC/75 ohm panel jack on standard S&W connector panel
Return loss…………………….. > -15 dB 100KHz to 270 MHz
Control Interface
GPI……………………………….. 2 x GPI
Format: TTL compatible, active low driven
Connector: BNC/75 ohm paneljack on standard S&W connector panel
RollCall …………………………. 1 x RollNet Interface
Format: 2.5 Mbit/s
Connector: BNC/75 ohm panel jack on standard S&W connector panel
Important Information
Please note that in order to support the IQLOG01 module and provide the ability to download Logo’s it is essential to have an Ethernet style RollCall Gateway card installed in the IQH3A frame. This is now fitted as standard into all new IQH3A-S frames, but customers adding IQLOG01 modules to existing frames must check both the type of 3U frame and version of gateway card installed. Compatible frames will have one of the following part numbers: IQH3A-E-0, IQH3A-E-P, IQH3A-S-0 and IQH3A-S-P.
Compatible gateway card part numbers are: RCIF3U2Y
(software version 3.5.12) or RCIF3U2B (software version 5.2.13)
Controls
Indicators
Power…………………………………………………….. OK (Green)
CPU running ………………………………………….. OK (Green flashing)
FPGA running ………………………………………… OK (Yellow flashing)
Status ……………………………………………………. OK (Green) / Warning (Yellow) / Error (Red)
Input ………………………………………………………. Active (Green)
SDI error……………………………………………….. Error (Red)
Controls
Video Controls
Input Loss Detect………………………………….. No Input or Invalid Standard
Input Standards List …………………………….. 525(480)/29i 625(576)/25i
Output Standard …………………………………… Manual
Select / Follows Input
Default Video
Output…………….. Pattern/ Black / Input / Logo
Pattern ………………………………………………….. Enable / H-Scroll
Pattern Type ………………….. 100% Color Bars, 75% Color Bars
SMPTE Bars, Tartan Bars, Pluge Ramp, H Sweep, Pulse & Bar, Burst
Used Snell IQLOG01 SD-SDI Logo Inserter
Used Snell IQLOG01 SD-SDI Logo Inserter